Відео

Good idea in how to change oil. But you are messy. If any of that oil gets to the deck belts. You will create more issues. Good luck.

What about the heated mirrors?

Thank you, Mr. Coffey! I read thru the instructions a few times and then watched your video. I'm 5' and installed it with minimum problems. I miss my dad being able to help me with projects.😢 Thank you for temporarily filling his shoes.

Dennis, you need to buy a lower steering shaft support/bushing and mount it up top in place of the crapy plastic bushing that is sloppy even when new. And your steering problems are over!

Thank you for that info.. very helpful for women who need a fix

Dennis have you ever seen the belt jump off track ? Put all 3 new pulleys on and new belt but it wants to jump. Any suggestions? Thanks same mower as you have

Just picked up an older shadow to start riding on and has some sticky switches. Thanks for the great vid buddy

Some of these zero turns you can adjust tracking while they are running and in gear. I've noticed with these Hustlers though, that you can't do it that way. Glad I found your video in hopes of tracking this Hustler straight.

I hope the bones of the deck are good.

I have a GT2254, the belt goes vertical then horizontal. Apparently the previous owner knew nothing therefore the belt isn't correctly installed. The diagrams are not detailed enough to see where the belt runs. Do you have a video changing this belt on this exact unit ? Apparently this is the only unit that moves this crazy change.

Hey, thanks for this video, I always look under my stuff for Grease fittings and some equipment like this are sealed and self lubing so I never saw these fittings on my husqvarna yth18542 ,which I believe is smaller version of yours,a 42” deck. Mine is going on its 3rd season and I’ve never greased the front end 😮. I’m definitely going to do this b4 I mow again this week

Thanks so much😊

A most eeeexcellent video Sir!

Great video. Very clear explanation. Awesome camera views too! Thank You

800000 thousand views 799999 is probably operators lol

As soon as I saw the handlebar mustache I knew this video would get me through this process. Thank you sir

Dave You have a type of grease recommendation? Thanks

Awesome! I'm going to try this!

So helpful!! How would you recommend doing 2 toggle bolts for the same piece of wood? I’m hanging up a closet shelf and using horizontal support board/beams to hold a floating shelf. The short side of the support beam only has 1 stud and it’s right in the middle. I am unsure if I should do 2 anchors (1 on each side of the stud) or if maybe I just need only one. Assuming I should do 2 to be safe, I wonder if you might be able to explain?

still useful, thanks

Dennis, thanks for the video. I have an MTD YardMachine 1 3 A M 7 6 2 F 0 5 2 (2008.) The issue is that the blades spin at idle but do increase in speed when PTO is ON. All springs are in the proper places, but when I engage/disengage my PTO handle, the idler pulley only moves a short distance. All suggestions are welcomed to understand why blades spin at idle. Thank you

Thank you! Great info.

7:40 Is it me, or is there a crack in that upper controlling arm? Thank you for the exceptionally well made and helpful video. Very generous.

Can you tell me what mandrel (deck) 0:58 spindles To get for YTH21K56 960450026 please?

This should be the default video . No bs, just what you need to know!

If you are sure the steering wheel is in the correct rotational position, you can take up much of the play with some hot melt glue in the gap. That stuff sticks to anything clean and dry pretty well. I strengthened the wheel covers on my 2000 Ford Expedition with some. I washed them and went around the entire inside with a bead of it. They are made in 2 pieces which can eventually come apart. If that happens, you are out $50 for each one, if Ford still has any available, which I doubt. Hot melt works quite well on anything which doesn't get hot. You can warm the parts if you have big pieces to assemble. That will give you time to get them in position before the stuff cools too much. Of course, the parts must be perfectly clean and dry for it to work. If you need to take stuff apart, just warm the parts with a heat gun until the glue softens.

Gravity! I can see the grease dripping down into the bottom bearing but how does it get into the upper bearing?

Thank you Dennis!!! You saved the day!

Good, Thx

If I may add, the sealed bearing is known as 2RS (2rubber seals) in its designation. Now the material in the new bearing is known as slushing compound. It is a combination of lubricant and anti-oxidizing agents. The amount installed at the bearings assembly is exact. The danger of grease is not under but over greasing. The oil carrier will dam in the elements and cause them to skid not roll. I am retired from SKF Bearing machine reliability division and we have a saying, "Grease gun or deadly weapon". To determine the proper amount of lubricant follow this simple formulae: SKF formula as follows. Multiply the bearing's outside diameter in inches by its width in inches, or height for thrust bearings. Then, add 0.114 to the product to get the amount of grease in ounces. This formula is widely accepted as an industry standard.

Thanks that was really useful man.

Fantastic explanation ❤

God bless you too

Thank you for your videos!

Gracias de mucha ayuda y con la información que necesitas de los focos

Do you still have the Honda Shadow? I just bought a 1999 750 ACE. Your maintenance videos on it are wonderful!

followed advice on greasing spindle bearing by removing the seals. had to as the replacement spindle died after one year. used leftover to open up and grease. thank you. really simple

Love these next time I'm gonna try to do my spindles shouldn't be too tuff Airens 46 in yard tractor ( Husqvarna), been a good one 22 I teck Briggs, best lawnmower motor I ever had, 11 years old

Just found you today when I needed refresher on my grease gun. Thanks for the clear step by step video. Problem I’m having is not enough hand strength anymore to pull the plunger & spring back far enough to lock it. Any suggestions?

maybe after removing the plastic from inside bearing faces , you might drill a couple hole in the outside plastic to let old grease flush out of bearing and be replaced by the new grease ? ?

Thank you sir. I had a tough time matching the four bolt pattern on mine. I am going to do the same thing you did and remove the shroud. I'm also getting the 2" 3/8 16 bolts. Your video was very informative and not dragged out. Straight to the point and explained plenty. Hunts

Can we see this on a cub cadet tractor?

Thanks again for this video. I’ve watched most of your Husqvarna videos. I’ve never used the cruise control on my 42 in lawn tractor and didn’t know how to start so I revisited this episode again to learn how. Much appreciation for all the info you provide.

Good video

Thanks again for this video. I’ve watched most of your Husqvarna videos. I’ve never used the cruise control on my 42 in lawn tractor and didn’t know how to start so I revisited this episode again to learn how. Much appreciate all the info you provide.

Hi Dennis, I subscribed to your channel right after changing the drive belt on my 15 year old Husqvarna. No wounds with your help. Thanks. 🤕

Thank you

Thank you so much. Help me a lot. God bless you.

Thanks

That yellow piece underneath the pad broke on mine. How do I replace it?